6A SMD RC-IGBT for Fridge Compressors – No Separate Freewheeling Diode Required
2026.11.20
3 次
PDGG006N065HRC RC-IGBT TO-252, integrated freewheeling diode for inverter refrigerator compressor drive board

For inverter refrigerator compressor drive boards, the IGBT and its freewheeling diode have long been two discrete components: separate packages, independent pads and individual circuit loops. The PDGG006N065HRC from Paidexineng integrates both devices into a single die within one TO‑252 package. The “RC” in the part number stands for this anti‑parallel diode‑integrated IGBT structure.

Below is the step‑by‑step guide for part selection: three key parameters, integrated freewheeling diode specs, thermal budget, two reliability indicators, and how to pick among the three family variants.

公众号推文翻译 (8).png


01Master the three core parameters first


Vcesat:At VGE=15V, IC=6A, 25°C, typical 1.70V, max 1.90V. At junction temperature of 150°C, typical Vcesat rises to 2.00V. This value dominates the conduction loss.

VF:Forward voltage of the built‑in diode is 1.60V at IF=6A, 25°C. Current flows through this path during freewheeling phase. Together with Vcesat, it determines total conduction loss over one switching cycle.

RthJC:Junction‑to‑case thermal resistance = 2.2°C/W. For the compact TO‑252 package, this parameter defines the sustainable continuous current rating.



02 The freewheeling diode is embedded inside the package


Traditional design uses a discrete IGBT for switching plus an external fast recovery diode for freewheeling. The RC‑IGBT integrates the anti‑parallel diode on the same silicon chip. One RC‑IGBT is used for upper and lower switches per bridge leg. The freewheeling path is shortened from PCB traces to inside the package. Benefits: one fewer component, reduced PCB footprint and fewer solder joints.

The integrated diode delivers solid performance: trr = 57ns @25°C / 62ns @150°C; Qrr = 0.33µC @25°C / 0.38µC @150°C; Peak reverse recovery current = 6.9A @25°C / 8.5A @150°C. Current rating matches the IGBT: IF=12A @TC=25°C, IF=6A @TC=100°C, IFM=30A.



03 2.2°C/W thermal resistance enables compact board design


Refrigerator compressor boards are constrained by limited space and weak airflow. TO‑252 is a surface‑mount package. Its large backside metal serves as the collector and can be soldered directly to heavy copper foil or aluminum substrate, creating a much shorter thermal path than through‑hole packages.

Key thermal ratings: Ptot = 70W @TC=25°C, 30W @TC=100°C; IC =12A @TC=25°C, 6A @TC=100°C. RthJA =60°C/W is a reference value without heat sink and rarely used for practical design. The 6A rating is defined at 100°C case temperature, leaving margin for transient conditions such as startup and defrost cycles.



04 Two critical reliability metrics: 0.20mJ & >8µs


Switching loss test condition: Vcc=400V, IC=6A, Rg=10Ω At 25°C: Eon=0.11mJ, Eoff=0.10mJ, total switching loss Ets=0.20mJ At 150°C: Eon≈0.10mJ, Eoff≈0.11mJ, total Ets=0.21mJ Total loss only increases by 0.01mJ from room temperature to 150°C.

Short‑circuit withstand capability: tsc >8µs at Vcc=300V, Tc=25°C. For compressor loads prone to locked rotor and reverse rotation, this spec is more valuable than low loss curves.

Additional electrical parameters: td(on): 20/18ns, tr:6/7ns, td(off):56/60ns, tf:88/98ns Qg=75nC, Cies=742pF, Coes=38pF, Cres=5pF Rg=13Ω, Vth typical 5.7V, VGE ±30V

Note: The maximum junction temperature rating is -40 ~ +175°C. 175°C is the absolute limit, not the recommended continuous operating temperature. Derating is required in hardware design.

05Three family variants — select by load requirement


The product family covers different power levels, voltage ratings and packages for diverse applications. Selection workflow: confirm system power & thermal budget first → check package compatibility → compare Vcesat and Ets.

  • 6A / 650V / TO‑252: PDGG006N065HRC | Refrigerator compressors, general motor drives, fans & range hoods

  • 15A / 650V / TO220F insulated package | Air conditioner compressors, where isolated mounting is needed

  • 25A / 1350V / TO‑247‑3 | Induction cookers, microwave ovens, high‑voltage high‑current scenarios

Contact Junmin Technology for full datasheets, samples or packaging consultation. This component is supplied in 2500PCS per reel. The current datasheet version Ver 1.3, updated Feb 2026, revised VGE and Vth parameters. Always refer to the latest revision for design.


? Typical Applications


Air conditioner compressors | Refrigerator compressors | Induction cookers